|
|
| |
|
| |
Using a manual style posthole digger is one way to dig
a single hole. But if you are digging more than one hole
for building a fence or a deck, it can take you forever
to dig your holes using a manual digger. Our powered earth
augers were conceived right from the start for medium
and heavy-duty earth drilling projects. From industrial
to commercial jobs, our post hole diggers readily handle
any drilling task. Our earth augers are low maintenance
and high quality pieces of equipment. The transmission is
made with hardened gears for longer life. Our design utilises
an 89mm centrifugal clutch delivering more than enough torque
to the earth drill. There are grips for operator comfort
and control and a kill switch located at the operator's
fingertips for extra safety. Our earth augers are designed
for years of trouble free service and are built tough
to last and perform beyond your expectations. |
| |
|
| |
Digging postholes using a post hole borer
Before you dig:
As with any project that requires digging beneath the
soil, check with your local authority and utility companies
to verify you are not digging into a gas, utility, sewer
or other buried cable or line. You will likely be held
liable for any damages you incur by digging if you have
not had these areas properly marked. Also, be sure to
obtain any necessary approvals or permits before you dig.
Always read and understand the owner's / operator's manual
prior to using any power tool.
Planning your dig:
You will need to lay out the perimeter of your project
so you can establish the location of your postholes. Although
this is not labour intensive, the success of your project
relies heavily on locating and marking the post hole locations
accurately.
|
| |
How do you dig a post-hole with our post hole digger?
When starting a new post-hole, drill about 75mm deep, then
shut off and remove all clumps of sod from the auger teeth.
This sod will prevent the auger from digging properly. Place
the auger back in the hole and proceed. About every 250
to 300mm you should release the throttle and pull it out
of the hole and tap the auger on the ground to remove the
dirt from your hole. Repeat this process until the desired
depth is reached. Always make sure the auger has stopped
before you insert or remove it from a hole. And as with
any power equipment, the owners manual should be completely
read and understood prior to using your post hole borer. |
| |
|
| |
 One
Man Powered Earth Borer
Digging made easy!
The PH980E is a one-man auger powered by an 85 cc /
3 HP American made Tecumseh® engine. It will take
earth augers from 50mm to 250mm in diameter and each is
762mm tall. There is an optional 457mm extension available.
Great for building decks, installing fences, and digging
tree planting holes or digging mailbox holes.
- PH980E, 3 HP, 85 cc engine 2 cycle
- Weight 14kg (30 lbs.).
- Bores any type of soil
- Drills down to 1.2m (4) deep
- Drill 50mm (2"), 100mm (4"), 150mm (6")
or 250mm (8) diameter post holes, depending on auger
size.
- 24 oz. fuel tank
- Vented fuel cap
- Automatic return throttle
- 18:1 gear reduction transmission
- Tillotson carburettor
- Shear pin and cotter pin for easy auger removal
- 25.4 mm (1") diameter output shaft
- Heavy duty flighting
- Full wrap around handle
- Easy to start and transport
 Made
with hardened gears for longer life- 89mm (3½) inch centrifugal clutch
- Rubber handle grips for operator comfort and control
- Kill switch located at the operator's fingertips
for extra safety
One man borer power head, without auger (see below
for augers) 12 month warranty $995.00 inc GST for power
head only.
Freight NI $25.00 SI $35.00
|
| |
|
| |
|
| |
 Two
Man Post Hole Borer
Our PH2000E is a two man auger powered by a 4 cycle,
5 HP American made Tecumseh® engine. It will take
earth drills from 50mm to 300mm in diameter and each are
762mm tall. There is an optional 457mm extension available.
Great for planting large shrubs, installing fences, building
decks and digging mailbox holes.
- PH2000E, 4 cycle, 5 HP Tecumseh® engine
with 24 oz. fuel tank
- Drills down to 1.2m (4) deep
- 50mm (2"), 100mm (4"), 150mm (6"),
200mm (8"), 250mm (10) and 300mm (12) diameter
holes
- Removable handlebars - Our post hole diggers are
easy to store and transport (engine stand supplied)
- Vented fuel cap
- Automatic return throttle
- 18:1 gear reduction transmission
- 89mm (3½") heavy duty centrifugal clutch
- Shear pin and Cotter pin for easy auger removal
- 23.4mm (1") diameter output shaft
- Heavy duty flighting
- Anti-Vibe rubber grips
- Kill switch located at the operator's fingertips
for extra safety
Two man borer power head, without auger (see below
for augers) 12 month warranty $1595 inc GST.
Freight NI $30.00 SI $45.00
|
| |
|
| |
|
| |
|
| |
Accessories
|
| |
Extension
Extension 457mm (18 ) Extension $135.00.
Freight NI & SI $10.00
|
| |
|
| |
Augers |
| |
 |
| |
Auger 200mm (8) $312.00.
Freight NI $20, SI $30.00
Auger 250mm (10) $380.00.
Freight NI $25, SI $35.00
Auger 300mm (12) $410.00.
Freight NI $25, SI $35.00 |
| |
|
| |
|
|
|
